How to Install Your Sun Brim
Installing your Sun Brim takes just seconds. Follow our simple step-by-step guide to get protected from the sun in no time.
Product-Specific Guides
Each Da Brim product has a slightly different installation method. Choose your product below for detailed instructions.
Da Brim Rezzo Visor
Attachment band system for cycling, skateboarding, climbing, paddling and equestrian helmets.
View guideDa Brim Sporty Cycling Brim
Full 360 degree brim for cycling helmets with hook and loop adjustment tabs. Tested to 35 mph.
View guideDa Brim Cycling Classic
Larger brim profile for cycling helmets with maximum sun coverage. Tested to 25 mph.
View guideDa Brim Equestrian Endurance
360 degree sun protection for equestrian helmets. Two installation methods for different helmet types.
View guideDa Brim Equestrian Petite
Smaller brim for petite riders. Two installation methods for different equestrian helmet types.
View guideDa Brim PRO Builder / Tech / Tech Lite
Visor for construction, climbing and work-at-height helmets. Strap-and-buckle attachment system.
View guideHow to Remove Your Da Brim
Removal is quick and easy. The method depends on your product type.
🚴 Cycling Brims (Sporty & Classic)
- Release the hook and loop adjustment tabs from the helmet straps.
- Lift the brim away from the helmet, detaching the hook and loop strips.
- Store the brim flat to maintain its shape.
🐴 Equestrian Brims (Endurance & Petite)
- Unfasten the hook and loop chin strap tabs.
- Gently pull the brim away from the helmet, releasing it from the visor pocket or hook and loop strips.
- Store the brim flat. Avoid bending or crushing.
🧢 Rezzo Visor
- Unsnap or unfasten the bill from the attachment band.
- Slide the attachment band off the helmet.
- Store the bill and band together. The friction tube can stay on the band.
For detailed step-by-step removal with tips, see your product's specific guide.
View product guides aboveTroubleshooting
Having issues? Here are solutions to common installation problems.
• Attachment band won't stay tight
Rezzo VisorMake sure the adjustment strap is fully tightened using your thumb as leverage. For rounded helmets without a rear hook, use the included friction tube to grip the helmet surface.
• Hook and loop fasteners don't hold
All productsInspect the fasteners for lint, dirt, or wear. Clean them gently or replace if worn. Always press firmly across the full surface when attaching. If fasteners no longer grip, discontinue use and contact us.
• Brim obstructs vision
All productsReinstall the brim at a higher angle or reposition it further back on the helmet. Check your peripheral vision by looking up, down, and side to side. If vision remains obstructed, the brim may not be compatible with your helmet.
• Brim catches wind at speed
Cycling brimsEnsure a gap of at least half an inch (12mm) between the bill and attachment band to relieve air pressure. The Sporty model is wind-tested to 35 mph and the Classic to 25 mph. Consider a lower-profile option for high-speed road cycling.
• Da Brim won't fit my helmet visor
Equestrian brimsFor equestrian helmets with a non-removable visor longer than 1 inch, use the pocket method (slide the brim over the visor). For flush-front helmets or removable visors, use the hook and loop strip method. See your product guide for details.
• Brim feels loose or detaches
All productsPull upward on the centre front of the brim to test. The assembly should not be loose or detach. Ensure the attachment band wraps around the helmet contours and sits below the front surface. Tighten all straps and re-secure fasteners.
Ready to Get Protected?
Browse our range of Sun Brims and find the perfect fit for your helmet.