✓ Da Brim PRO Builder / Tech / Tech Lite

How to Install Your Da Brim PRO Helmet Visor

The Da Brim PRO line is made with the high quality and durability that professionals and their work environments demand. Installation is quick and easy. No tools required.

✓ No tools required

For construction, climbing & work-at-height helmets

Important Safety Information

The PRO helmet visor sunshade product is designed to be installed to a construction, climbing or work-at-height helmet only.
Do not use the Da Brim visor other than as instructed. Do not modify the product.
This product should not be used with helmets that have a non-removable visor.
Failure to properly seat the visor could result in it unseating during use, startling you or others, or obstructing your vision, which may lead to serious injury or death.

Watch the Installation

Step-by-Step Installation

Begin with a Loose Adjustment Strap

Start with the adjustment strap fully loosened so the band is at its widest.

💡 Tip: If your helmet has a removable visor, remove it before installing the Da Brim. This product should not be used with helmets that have a non-removable visor.

Hold the Helmet and Position the Band

Hold your helmet at the centre back with your thumb on the outside and grip the centre back loop of the Da Brim visor at the same place with your thumb.

💡 Tip: Keep a firm grip so both the helmet and visor stay aligned.

Seat the Visor on the Helmet

Place your other hand at the front of the product and rotate the assembly upside down. Push the helmet against your chest and slowly pull the visor over the helmet, seating the visor edge on the helmet. The black underside of the product should end at the bottom edge of the helmet.

⚠ Important: Failure to properly seat the Da Brim visor could result in it unseating during use, which may lead to serious injury.

💡 Tip: Work slowly and evenly to avoid the visor sitting crooked.

Flip Over and Tighten the Strap

Flip the assembly over and tighten the strap by positioning your thumb at the rear of the helmet and pulling on the strap. Tuck the strap into the hole provided.

💡 Tip: The visor should feel snug and not wobble when you shake the helmet.

Check for Correct Installation

Centres of the helmet and Da Brim helmet visor should align; if necessary, pull to straighten. Always ensure the strap is tight. The Da Brim visor should always seat below the front helmet surface, as shown, to prevent detachment. Check by pulling upward on the front visor as if in wind flow. The product should not be loose or detach from the helmet.

⚠ Important: Failure to properly seat the Da Brim visor could result in it unseating during use, which may lead to serious injury.

💡 Tip: If the product does not seat as described, do not use it with this helmet. Failure to properly seat the visor could result in it unseating during use and startling you or others, or obstructing your vision, which may lead to serious injury or even death.

Fit Helmet and Test Your Vision

After the visor is installed on the helmet, follow the helmet manufacturer's instructions for fitting the helmet. Then, while the helmet and Da Brim visor are fitted, and prior to using the helmet and visor in any activity, check to ensure that the visor does not obstruct your vision. Pay attention to your peripheral vision. Should your vision be obstructed by the visor, remove the helmet and reinstall the helmet visor.

💡 Tip: Look up, down, and side to side to ensure full range of vision. After proper installation, your vision should not be obstructed.

How to Remove the Da Brim PRO Visor

Always remove the Da Brim when stationary and in a safe location.

Wait until you are at a safe location and at a rest position.

Disengage the visor by releasing the tension on the strap. Pull up on the buckle.

Pull up on the visor and remove it from the helmet.

Shop Da Brim PRO Visors

Built for professionals. Designed to withstand demanding work environments.

Browse Products View FAQ

Helmet Brims