How to Install Your Da Brim Equestrian Endurance
The Da Brim Equestrian Endurance helmet visor is designed for equestrian helmets, providing broad 360 degree UPF50+ sun protection. Installation varies depending on your helmet type.
Important Safety Information
- The Equestrian Endurance Da Brim is designed for equestrian sporting activities only.
- It is not designed for motorised sports, helmets and classes 5 and 6 whitewater helmets, bicycle helmets, or any activity other than equestrian sports while wearing an equestrian helmet.
- Do not use the Da Brim other than as instructed and do not modify the Da Brim.
- Obstruction of your vision can cause a crash and may lead to serious bodily injury or even death.
- Make sure the fasteners in the pocket are sealed and that the pocket does not obstruct your vision after installation.
Watch the Installation
Which installation method do I use?
The Equestrian Endurance Da Brim can be used with two types of equestrian helmets:
- Section 1: Helmets with a non-removable visor greater than 1 inch in width. Use the pocket feature to install.
- Section 2: Helmets with a flush front, removable visor, or pre-moulded lip up to 1 inch in width. Remove the visor first, then install.
Section 1: Non-Removable Visor (Over 1 Inch)
For helmets with a non-removable visor greater than 1 inch in width. Use the pocket feature to install.
Begin with a Loose Adjustment Strap
Start with the adjustment strap fully loosened before installation.
Open the Front Pocket
Open the front pocket by separating the hook and loop fasteners. Insert the helmet's non-detachable visor into the pocket. Do not close the pocket fasteners yet.
Pull Down and Seat the Da Brim
Pull the rear of the Da Brim visor down and seat the Da Brim on the helmet. Make sure the crown of the Da Brim is level around the helmet's circumference and does not interfere with where your ears will sit.
Tighten the Strap
Make sure the visor is as far inside the pocket as possible when the front of the Da Brim visor is resting flat against the front of the helmet. Tighten the strap by positioning your thumb at the rear of the helmet and pulling on the strap a few times. Tuck the strap into the hole provided.
Close the Front Pocket Fasteners
Close the fasteners on the front pocket by mating the hook and loops. Make sure the pocket is tightly closed. The brim should not be buckled or bowed. Double check the tightness of the strap.
Check for Correct Installation
Centres of the helmet and Da Brim visor should align. Always ensure the strap is tight. The Da Brim visor should always seat in a level plane around the helmet with the front pocket tightly closed, to prevent detachment. Inspect hook and loop fasteners regularly for wear. If the fasteners do not function properly, discontinue use of this product. Check by pulling upward on the front visor as if in wind flow. The Da Brim visor should not be loose or detach from the helmet.
Fit Your Helmet and Test Vision
After the Da Brim visor is installed on the helmet, follow the helmet manufacturer's instructions for fitting the helmet. Then, while the helmet and Da Brim product is fitted, and prior to using it in an activity, check to ensure that the Da Brim visor does not obstruct your vision. Pay attention to your peripheral vision. Should your vision be obstructed, remove the helmet and reinstall the Da Brim visor.
Section 2: Removable Visor or Flush Front
For helmets with a flush front, removable visor, or pre-moulded lip up to 1 inch in width. Remove the visor first.
Begin with a Loose Adjustment Strap
Start with the adjustment strap fully loosened before installation.
Grip the Centre Back of the Helmet
Hold your helmet at the centre back with your thumb on the outside and grip the centre back loop of the Da Brim visor at the same place with your thumb.
Rotate and Seat the Visor
Place your other hand at the front of the Da Brim visor and rotate the assembly upside down. Push the helmet against your chest and slowly pull the Da Brim visor over the helmet, seating the visor's edge on the helmet. The black underside of the Da Brim should end at the bottom edge of the helmet.
Flip Over and Tighten the Strap
Flip the assembly over and tighten the strap by positioning your thumb at the rear of the helmet and pulling on the strap. Tuck the strap into the hole provided.
Check for Correct Installation
Centres of the helmet and Da Brim visor should align. If necessary, pull to straighten. Always ensure the strap is tight. The Da Brim visor should always seat below the front helmet surface, as shown, to prevent detachment. The front pocket should be closed and have a low profile. Inspect hook and loop fasteners regularly for wear. If the fasteners do not function properly, discontinue use of this product. Check by pulling upward on the front visor as if in wind flow. The Da Brim visor should not be loose or detach from the helmet.
Fit Your Helmet and Test Vision
After the Da Brim visor is installed on the helmet, follow the helmet manufacturer's instructions for fitting the helmet. Then, while the helmet and Da Brim visor is fitted, and prior to using it in an activity, check to ensure that the Da Brim visor does not obstruct your vision. Pay attention to your peripheral vision. Should your vision be obstructed, remove the helmet and reinstall the Da Brim visor.
How to Remove the Da Brim
Always remove the Da Brim when stationary and in a safe location.
Wait until you are at a safe location and at a rest position.
Disengage the Da Brim visor by releasing the tension on the strap by pulling up on the buckle.
Pull up on the rear of the Da Brim visor and remove.
Shop the Da Brim Equestrian Endurance
Available in Black and Grey. 360 degree UPF50+ sun protection for riders.